interface cp2102 gmr(qfn28)

758 results for "interface cp2102 gmr(qfn28)"

spiral test

some files emerging in the development of a digital percussive interface

lleck

0

PSWS Xerxes dual

An SDR dual using ADC2808 converters and an FX-3 USB3 interface

wittend

0

multiboard controller

1:8 USB 2.0 and RS-232 interface board

eridgraves

0

openlst hw

Open-source hardware and software for a satellite with a custom on-board computer to interface over I2C, SPI, and UART with a flash chip, IMU, barometer, camera, and thermal sensors. Built to fit within a 1U form factor.

LP2981-3.3

CC1110

AP6502

ASFL1-27.000MHZ

MIC803

harmalkar

1

VERTECS CCB A

The VERTECS CCB, is an open-source payload interface board leveraging Commercial Off-The-Shelf (COTS) components with a Raspberry Pi Compute Module 4 at its core. Originally developed for the VERTECS 6U Astronomical Nanosatellite, the board has been opened-sourced and made available for use in future nanosatellite projects.

ezrafielding

7

stepper driver

Motor mounted stepper driver with step and direction controls and a UART interface

janelia-kicad

3

8 Bit CPU 32k

Version 3 of my educational DIY TTL computer built around a UART serial interface - now with blinkenlights!

slu4coder

42

Output

A USB audio dongle with Cirrus Logic CS43198 DAC and FPGA-based USB interface.

nonameCCC

0

FMC MIPI v2

FMC card to allow interfacing Xilinx FPGA boards with Jetson TX2 or TX1 via CSI-2 camera interface

VideoGPU

22

AbuDhabi ElectronBeam

This is a project done at EST-RUB. Here is the control and interface of a vacuum system using a Pfeiffer turbo pump plus a backing pump

monicaespinosa

1

Final PCB

This is a project done at EST-RUB. Here is the control and interface of a vacuum system using a Pfeiffer turbo pump plus a backing pump

monicaespinosa

1

LP SC PCB

This is a project done at EST-RUB. Here is the control and interface of a vacuum system using a Pfeiffer turbo pump plus a backing pump

monicaespinosa

1

SensorPCB

This is a project done at EST-RUB. Here is the control and interface of a vacuum system using a Pfeiffer turbo pump plus a backing pump

monicaespinosa

1

anode1

This is a project done at EST-RUB. Here is the control and interface of a vacuum system using a Pfeiffer turbo pump plus a backing pump

monicaespinosa

1

anode2

This is a project done at EST-RUB. Here is the control and interface of a vacuum system using a Pfeiffer turbo pump plus a backing pump

monicaespinosa

1

anode3

This is a project done at EST-RUB. Here is the control and interface of a vacuum system using a Pfeiffer turbo pump plus a backing pump

monicaespinosa

1

Platte

This is a project done at EST-RUB. Here is the control and interface of a vacuum system using a Pfeiffer turbo pump plus a backing pump

monicaespinosa

1

Platte signal cond

This is a project done at EST-RUB. Here is the control and interface of a vacuum system using a Pfeiffer turbo pump plus a backing pump

monicaespinosa

1

A2USB IRQExtension

This projects provides alternate firmware for A2VGA cards to add USB support to the Apple II. It currently supports a USB mouse and fully emulates an Apple II Mouse Interface Card.

ThorstenBr

24

compact schematic

GardenEye is an IoT solution for monitoring and managing garden environments. It consists of an embedded system that collects data from various sensors and a web application that provides a user-friendly interface for visualizing and analyzing the collected data.

Etto48

0

compact schematic

GardenEye is an IoT solution for monitoring and managing garden environments. It consists of an embedded system that collects data from various sensors and a web application that provides a user-friendly interface for visualizing and analyzing the collected data.

Etto48

0

Reference electronics designs for interface cp2102 gmr(qfn28) – Page 6 | Open App Note