badges
sophiayduan
hackathon pcb badges
Components (46)
| Reference | Value | Description |
|---|---|---|
| Q1 | AO3400A | 30V Vds, 5.7A Id, N-Channel MOSFET, SOT-23 |
| Q2 | Si1308EDL | N-MOSFET transistor, drain/source/gate |
| U1 | W25Q32JVSS | 32Mbit / 4MiB Serial Flash Memory, Standard/Dual/Quad SPI, 2.7-3.6V, SOIC-8 (208 mil) |
| U2 | RP2040 | A microcontroller by Raspberry Pi, Dual ARM Cortex-M0+, 133MHz, no flash, 264KB SRAM, 8 PIO state machines, VQFN-56 |
| U3 | LIS2DH | 3-Axis Accelerometer, 2/4/8/16g range, I2C/SPI interface, LGA-14 |
| U4 | CH592F | RISC-V core Bluetooth LE 5.4 MCU, USB 2.0 host / device, segment LCD driver, SPI, I2C / SMBus, 4 UART, 12-bit ADC, touch-key detection module, WQFN-28 |
| U5 | USBLC6-2SC6 | Very low capacitance ESD protection diode, 2 data-line, SOT-23-6 |
| U6 | TP4056-42-ESOP8 | 1A Standalone Linear Li-ion/LiPo single-cell battery charger, 4.2V ±1% charge voltage, VCC = 4.0..8.0V, SOIC-8 (SOP-8) |
| U7 | AP2112K-3.3 | 600mA low dropout linear regulator, with enable pin, 3.8V-6V input voltage range, 3.3V fixed positive output, SOT-23-5 |
| AE2 | Antenna_Shield | Antenna with extra pin for shielding |
| BZ1 | Buzzer | Buzzer, polarized |
| C1,C2 | 33pF | Unpolarized capacitor |
| C3-C5,C9-C16,C22,C41 | 100nF | Unpolarized capacitor |
| C6,C8,C28-C37 | 1uF | Unpolarized capacitor |
| C7,C39 | 10uF | Polarized capacitor,Unpolarized capacitor |
| C21 | 100uF | Unpolarized capacitor |
| C23 | 0.47uF | Unpolarized capacitor |
| C24,C26,C27,C38,C40 | 4.7uF | Unpolarized capacitor |
| C25 | 2.2uF | Unpolarized capacitor |
| D1,D2,D4,D5,D7,D12-D16,D20,D21 | SK6812 | RGB LED with integrated controller |
| D3 | D | Diode |
| D6 | RED | Light emitting diode |
| D8 | NOT RED | Light emitting diode |
| D9-D11 | MBR0530 | 30V 0.5A Schottky Power Rectifier Diode, SOD-123 |
| FB1 | BLM18AG601SN1D | Ferrite bead |
| H1,H2 | MountingHole | Mounting Hole with connection |
| J1 | Conn_02x03 | Generic connector, double row, 02x03, counter clockwise pin numbering scheme (similar to DIP package numbering), script generated (kicad-library-utils/schlib/autogen/connector/) |
| J2 | USB_C_Receptacle_USB2.0_16P | USB 2.0-only 16P Type-C Receptacle connector |
| J3 | E-INK | Generic connector, single row, 01x24, script generated (kicad-library-utils/schlib/autogen/connector/) |
| J4 | LiPo | Generic connector, single row, 01x02, script generated (kicad-library-utils/schlib/autogen/connector/) |
| J5 | Conn_01x03 | Generic connector, single row, 01x03, script generated (kicad-library-utils/schlib/autogen/connector/) |
| L1 | 10uH | Inductor |
| L2 | 68uH | Inductor |
| R1,R8,R13,R14 | 330R | Resistor |
| R2,R6,R11 | 10k | Resistor |
| R3,R7 | 1k | Resistor |
| R4,R5 | 27.4R | Resistor |
| R9,R10 | 5.1k | Resistor |
| R12 | 0.47R | Resistor |
| R15 | 2.2k | Resistor |
| R16,R17 | 4k7 | Resistor |
| SW1 | RESET | Push button switch, generic, two pins |
| SW2 | BOOTSEL | Push button switch, generic, two pins |
| SW3-SW10 | SW_Push | Push button switch, generic, two pins |
| Y1 | 12MHz | Four pin crystal, GND on pins 2 and 4 |
| Y2 | 32MHz | Four pin crystal, GND on pins 2 and 4 |