firestarter
hstarmans
Kicad design files for prism laser direct imager using up5k FPGA and ESP32
Components (42)
| Reference | Value | Description |
|---|---|---|
| IC1-IC3 | TMC2209-LA-T | Bipolar Motor Driver Power MOSFET Step/Direction, UART 28-QFN (5x5) |
| IC4 | DMP6023LSS-13 | MOSFET P-Ch 60V Enh Mode 20Vgs 53.1nC 2569pF |
| Q1 | Q_NMOS_GDS_spindle | N-MOSFET transistor, gate/drain/source |
| Q2 | Q_NMOS_GSD_fan | N-MOSFET transistor, gate/source/drain |
| U1 | MCP1700T-1202ETT | 250mA Low Quiscent Current LDO, 1.2V output, SOT-23 |
| U2 | ESP32-S3-WROOM-2 | 2.4 GHz WiFi (802.11 b/g/n) and Bluetooth ® 5 (LE) module Built around ESP32S3 series of SoCs, Xtensa ® dualcore 32bit LX7 microprocessor Flash up to 16 MB, PSRAM up to 8 MB 36 GPIOs, rich set of peripherals Onboard PCB antenna |
| U3 | LM1117MPX-5.0/NOPB | 800mA Fixed Low Drop Positive Voltage Regulator, Fixed Output 5.0V, SOT-223 |
| U4 | MCP1700-1502 | 250mA Low Quiscent Current LDO, 1.2V output, SOT-23 |
| U5 | ICE40UP5K-SG48ITR-FPGA_Lattice | |
| U6 | MCP1700T-2802E | 250mA Low Quiscent Current LDO, 1.2V output, SOT-23 |
| U7 | USBLC6-2SC6 | Very low capacitance ESD protection diode, 2 data-line, SOT-23-6 |
| U8 | AP63203WU-7 | 2A, 1.1MHz Buck DC/DC Converter, fixed 5.0V output voltage, TSOT-23-6 |
| C1,C2,C4,C7-C11,C13,C15-C17,C19-C21,C23,C27-C30,C40,C41,C45-C47,C49-C51,C53-C55 | 10uF | Unpolarized capacitor |
| C3,C5,C6,C12,C14,C18,C22,C24,C25,C31,C33,C35,C37-C39,C48,C52,C57 | 0.1uF | Unpolarized capacitor, small symbol |
| C26 | 470uF | |
| C32,C34,C36 | 22nF | |
| C42-C44 | 100uF | |
| C56 | 100pF | Unpolarized capacitor, small symbol |
| D1 | D_Zener | Dual Zener diode, common anode on pin 2 |
| D2 | LED_ABGR | RGB LED, anode/blue/green/red |
| D4 | D_TVS | Bidirectional transient-voltage-suppression diode |
| D5,D7,D8 | SS24FL | 40V 2A Schottky Diode, SMA |
| D6 | D_Schottky | Schottky diode |
| F1 | 8V 1.1A | Fuse |
| F2 | 24V 3.0A | |
| FB1 | 600R / 1.5A @ 100MHz | Ferrite bead, small symbol |
| FL1 | 0603USB-951 | Coilcraft common mode choke, 500mA, 250VAC, 63nH, 142mohm, 2.8Ghz |
| J1 | USB_C_Receptacle_USB2.0_16P | USB 2.0-only 16P Type-C Receptacle connector |
| J2 | FH12A-24S-0.5SH | Generic connectable mounting pin connector, single row, 01x24, script generated (kicad-library-utils/schlib/autogen/connector/) |
| J3 | 2-84952-0 | Generic connectable mounting pin connector, single row, 01x20, script generated (kicad-library-utils/schlib/autogen/connector/) |
| J4 | DC_Jack_5.5x2.5 | DC Barrel Jack with an internal switch |
| J6-J8 | heatsink_tmc | Generic connector, single row, 01x01, script generated (kicad-library-utils/schlib/autogen/connector/) |
| J9 | spindle | Generic connector, single row, 01x02, script generated (kicad-library-utils/schlib/autogen/connector/) |
| J13 | fan | Generic connector, single row, 01x02, script generated (kicad-library-utils/schlib/autogen/connector/) |
| JX1,JY1,JZ1 | Motor | |
| L1,L2 | 10uH | Inductor, small symbol |
| R2-R7,R21,R26,R28-R31 | 5.1K | Resistor |
| R8,R9 | 1.5K | Resistor |
| R10,R22,R23 | 100 | Resistor |
| R13,R14,R17-R20 | 0.11 | |
| R27 | 71.5K | Resistor |
| SW1,SW2 | SW_Push_Open | MEC 5E single pole normally-open tactile switch |