sertest-ng
eurovibes
Components (40)
| Reference | Value | Description |
|---|---|---|
| U101,U106 | M24C64-RMN | 2Kb (256x8) I2C Serial EEPROM, 1.8-5.5V, SOIC-8 |
| U102,U301 | USBLC6-2SC6 | Very low capacitance ESD protection diode, 2 data-line, SOT-23-6 |
| U103 | STM32G431RBTx | STMicroelectronics Arm Cortex-M4 MCU, 128KB flash, 32KB RAM, 170 MHz, 1.71-3.6V, 52 GPIO, LQFP64 |
| U104 | ATECC608B-MAVDA-S | Cryptographic Co-Processor with Secure Hardware-based 16 Key Storage, ECDSA and ECDH support, I2C, UDFN-8 |
| U105 | AMS1117-3.3 | 1A Low Dropout regulator, positive, 3.3V fixed output, SOT-223 |
| U201 | ADM213 | 0.1 μF, 5V powered CMOS RS-232 120kb/s transceiver with 4 drivers and 5 receivers (tx/rx: 4/5; 2 receivers active in shutdown), shutdown / enable pins, SOIC-28 / SSOP-28 |
| U202 | SP330 | RS-232/RS-485/RS-422 Transceiver with 1.65V-5.5V Interface |
| U302 | XC6206P332MR | Positive 60-250mA Low Dropout Regulator, Fixed Output, SOT-23 |
| U303 | CH340N | USB serial converter, 2Mbps, UART, JEITA SOIC-8 (SOP-8) |
| U401 | TJA1042T | High-Speed CAN Transceiver, standby mode, split pin, SOIC-8 |
| C101,C102 | 20p | Unpolarized capacitor |
| C103,C104 | 12p | Unpolarized capacitor |
| C105 | 1F | Polarized capacitor |
| C106,C108,C110,C111,C113-C116,C201-C208,C303,C304 | 100n | Unpolarized capacitor |
| C107,C109,C112 | 10µ | Unpolarized capacitor |
| C301,C302 | 1µ | Unpolarized capacitor |
| C401 | 4n7 | Unpolarized capacitor |
| D101 | 1N4148WS | 75V 0.15A Fast Switching Diode, SOD-123 |
| D102-D106,D301 | LED | Light emitting diode |
| D201-D214,D401,D402 | RI | Dual LED, cathodes on pins 1 and 4 |
| FB101,FB102,FB201,FB202,FB301,FB401 | Ferrite | Ferrite bead, small symbol |
| J101,J301 | USB | USB 2.0-only 16P Type-C Receptacle connector |
| J201 | Debug | 9-pin D-SUB connector, socket (female), Mounting Hole |
| J202 | RS-232 | 9-pin D-SUB connector, socket (female), Mounting Hole |
| J203 | RS-485/422 | Generic connector, single row, 01x04, script generated (kicad-library-utils/schlib/autogen/connector/) |
| J401,J402 | CAN | 9-pin D-SUB connector, pins (male), Mounting Hole,Generic connector, single row, 01x02, script generated (kicad-library-utils/schlib/autogen/connector/) |
| JP401 | CAN_GND | Jumper, 2-pole, open |
| R101,R110-R114,R116,R201-R212,R217-R232,R303,R401-R404 | 1k | Resistor |
| R102-R105,R301,R302 | 5k1 | Resistor |
| R106 | 1M | Resistor |
| R107 | 22 | Resistor |
| R108,R109 | 33 | Resistor |
| R115 | 10k | Resistor |
| R213-R216 | 0 | Resistor |
| R405,R406 | 60 | Resistor |
| R407,R408 | 100 | Resistor |
| SW101 | Reset | Push button switch, generic, two pins |
| SW401 | Term | Momentary Switch, dual pole double throw |
| Y101 | 8MHz | Two pin crystal |
| Y102 | 32k | Two pin crystal |