| IC1 | ESP32-S3-WROOM-1U-N16 | Multiprotocol Modules SMD Module, ESP32-S3, 16 MB SPI Flash, IPEX Antenna Connector |
|---|
| Q1,Q2 | NPN | Bipolar transistor symbol for simulation only, substrate tied to the emitter |
|---|
| U1 | ADXL375BCCZ-RL7 | |
|---|
| U2 | USBLC6-2P6 | |
|---|
| U3 | MS5607-02BA | Barometric pressure sensor, 20cm resolution, 10 to 1200 mbar, I2C and SPI interface up to 20MHz, LGA-8 |
|---|
| U4,U12 | ICM-20948 | InvenSense 9-Axis Motion Sensor, Accelerometer, Gyroscope, Compass, I2C/SPI, QFN-24 |
|---|
| U5 | MCP2542FDxMF | CAN-FD Transceiver, Wake-Up on CAN activity, 8Mbps, 5V supply, STBY pin, 3x3 DFN-8 |
|---|
| U6 | LM1085-3.3 | 3A 27V Linear Regulator, Fixed Output 3.3V, TO-220/TO-263 |
|---|
| U7 | LM1085-5.0 | 3A 25V Linear Regulator, Fixed Output 5.0V, TO-220/TO-263 |
|---|
| U8 | AMS1117-1.8 | 1A Low Dropout regulator, positive, 1.8V fixed output, SOT-223 |
|---|
| U9,U10 | INA233 | High-Side or Low-Side Measurement, Bi-Directional Current and Power Monitor (0-36V) with I2C, SMBus-, and PMBus-Compatible Interface, VSSOP-10 |
|---|
| U11 | CP2102N-Axx-xQFN24 | USB to UART master bridge, QFN-24 |
|---|
| C1-C6,C13,C15-C18,C21,C24-C27 | 0.1uF | Unpolarized capacitor |
|---|
| C7-C11 | 10uF | Unpolarized capacitor |
|---|
| C12 | 22uF | Unpolarized capacitor |
|---|
| C14 | 47uF | Unpolarized capacitor |
|---|
| C19 | .1uF | Unpolarized capacitor |
|---|
| C20 | 4.7uF | Unpolarized capacitor |
|---|
| C22 | 22u | |
|---|
| C23 | 1uF | Unpolarized capacitor |
|---|
| D1-D6 | D | Diode |
|---|
| D7-D9 | GREEN | |
|---|
| F1 | Polyfuse | Resettable fuse, polymeric positive temperature coefficient |
|---|
| F2 | 5V/3A | Fuse |
|---|
| FB1 | BLM21PG221 | |
|---|
| J1 | Conn_01x05_Socket | Generic connector, single row, 01x05, script generated |
|---|
| J2 | Conn_01x02 | Generic connector, single row, 01x02, script generated (kicad-library-utils/schlib/autogen/connector/) |
|---|
| J3,J7 | Conn_01x06_Pin | Generic connector, single row, 01x06, script generated |
|---|
| J4 | USB_C_Receptacle_USB2.0 | |
|---|
| J5 | Conn_01x04 | |
|---|
| J6 | Conn_01x02_Socket | Generic connector, single row, 01x02, script generated |
|---|
| R1 | 120 | Resistor, US symbol |
|---|
| R2,R3 | 200m | Resistor, US symbol |
|---|
| R4,R13,R16,R20,R21 | 1k | Resistor, US symbol |
|---|
| R5,R6 | 0 | Resistor, US symbol |
|---|
| R7,R8 | 12k | Resistor, US symbol |
|---|
| R9,R10 | 5.1k | Resistor, US symbol |
|---|
| R11 | 22.1k | Resistor, US symbol |
|---|
| R12 | 47.5k | Resistor, US symbol |
|---|
| R14,R15 | 22 | Resistor, US symbol |
|---|
| R17,R18 | 4.7k | Resistor, US symbol |
|---|
| R19 | 220 | Resistor, US symbol |
|---|
| SW1 | EN | Push button switch, generic, two pins |
|---|
| SW2 | BOOT | Push button switch, generic, two pins |
|---|
| TP3 | 5V | test point |
|---|
| TP4 | V_BUS | test point |
|---|
| TP5 | 3V3 | test point |
|---|
| TP6 | V_BATT | test point |
|---|
| TP7 | 1V8 | test point |
|---|
| TP8 | V_USB | test point |
|---|
| TP9 | D- | test point |
|---|
| TP10 | D+ | test point |
|---|
