NoNameComputer-2.0
PlanAndBuild
The NoNameComputer 2.0 AKA NNCpro is being designed for mid-high power rockets and other flying vehicle. It will be equipped with various sensors like barometers, IMUs, magnetometer, current sensing etc.
Components (59)
| Reference | Value | Description |
|---|---|---|
| IC1 | LSM6DSV80XTR | 6-axis IMU (inertial measurement unit) with high-g accelerometer, embedded AI, and sensor fusion for wearables and |
| IC2 | TPS56C230RJER | Switching Voltage Regulators 4.5-V to 18-V, 12-A synchronous buck converter 20-VQFN-HR -40 to 125 |
| Q1-Q7 | DO2300B | 0.115A Id, 60V Vds, N-Channel MOSFET, SOT-23 |
| Q8 | SI1016CX-T1-GE3 | Mosfet Array 20V 220mW Surface Mount SC-89 (SOT-563F) |
| U1 | W25Q128JVE | 128Mbit / 16MiB Serial Flash Memory, Standard/Dual/Quad SPI, 2.7-3.6V, WSON-8 |
| U6 | STM32H562RIVx | STMicroelectronics Arm Cortex-M33 MCU, 2048KB flash, 640KB RAM, 250 MHz, 1.62-3.6V, 53 GPIO, VFQFPN68 |
| U7 | MS5611-01BA | Barometric pressure sensor, 10cm resolution, 10 to 1200 mbar, I2C and SPI interface up to 20MHz, LGA-8 |
| U8 | BMP390L | |
| U9 | MMC5983MA | |
| U10 | LSM6DSO32 | |
| U11 | H3LIS200DLTR | |
| U12 | TPS564242DRLR | |
| U15 | INA3221 | Triple-Channel High-Side Shunt and Bus Voltage Monitor with I2C and SMBUS Compatible Interface, QFN-16 |
| U16,U17 | E220-400M22S | |
| U18,U19 | 74LVC2G04LT06ARCQ | Dual schmitt inverter |
| U20 | PCA9685BS | 16-channel 12-bit PWM Fm+ I2C-bus LED controller RGBA QFN |
| U21 | LT6000CDCB#TRMPBF | |
| U22 | NC7WZ07P6X | |
| U23 | MAX-M10M-20B | |
| BZ1 | Buzzer | Buzzer, polarized |
| C1,C5,C7-C10,C12-C16,C18,C19,C22-C24,C28,C29,C32,C34,C39-C44,C46,C48-C50,C52,C53,C56 | 100nF | Unpolarized capacitor |
| C2,C11,C20,C30,C51 | 1uF | Unpolarized capacitor |
| C3,C4 | 2.2uF | Unpolarized capacitor |
| C6 | 4.7uF | Unpolarized capacitor |
| C17,C21,C45,C47,C55 | 10uF | Unpolarized capacitor |
| C25-C27,C31,C33 | 22uF | Unpolarized capacitor |
| C35-C38 | 47uF | Unpolarized capacitor |
| C54 | 10nF | Unpolarized capacitor |
| D4,D5,D8,D9,D12,D13 | D | Schottky diode |
| D6,D7,D10,D11,D14-D17,D21-D24 | LED | Light emitting diode |
| D18-D20 | WS2812B-2020 | RGB LED with integrated controller, 2.0 x 2.0 mm, 12 mA |
| D25-D27 | SP15100L | |
| F1-F6 | 500mA | Fuse |
| FB1-FB3 | 600ohm | Ferrite bead |
| J1-J7 | Screw_Terminal_01x02 | Generic screw terminal, single row, 01x02, script generated (kicad-library-utils/schlib/autogen/connector/) |
| J8,J9 | Conn_01x02_Pin | Generic connector, single row, 01x02, script generated |
| J10,J11,J19 | Conn_Coaxial | coaxial connector (BNC, SMA, SMB, SMC, Cinch/RCA, LEMO, ...) |
| J12 | USB_C_Receptacle_USB2.0_16P | USB 2.0-only 16P Type-C Receptacle connector |
| J13 | MEM2052-00-195-00-A_REVA | |
| J14-J18,J20-J22 | Conn_01x03_Pin | Generic connector, single row, 01x03, script generated |
| L1,L4 | 27nH | Inductor |
| L3 | 7443934450068 | WE-XHMI Performance SMT Power Inductor Size 6030; L = 0.68 H +/-20%; IR = 30 A; Isat = 22.3 A; RDCmax = 3.4 m |
| L5 | AFE201612S1R5MBT | |
| R1-R4,R7-R11,R30,R34,R36-R38,R42,R44-R46,R50,R52-R60,R68,R76 | 10kΩ | Resistor |
| R5,R6 | 4.7kΩ | Resistor |
| R12 | 330kΩ | Resistor |
| R13,R20,R33,R35,R41,R43,R49,R51,R70,R72 | 100kΩ | Resistor |
| R14,R16 | 15kΩ | Resistor |
| R15 | 110kΩ | Resistor |
| R17 | 135kΩ | Resistor |
| R18 | 30kΩ | Resistor |
| R19 | 42.2kΩ | Resistor |
| R21-R23 | 0.03Ω | Resistor |
| R24-R29,R31,R32,R39,R40,R47,R48,R71 | 10Ω | Resistor |
| R61,R62,R65-R67,R73,R74 | 220Ω | Resistor |
| R63,R64 | 5.1kΩ | Resistor |
| R69 | 560Ω | Resistor |
| R75 | 1kΩ | Resistor |
| Y1 | Crystal_GND24 | Four pin crystal, GND on pins 2 and 4 |