Loading design…
MetalMusings
Documentation accompanying the "Make My Own EtherCAT device" video serie on Youtube.
| Reference | Value | Description |
|---|---|---|
| U1,U3,U4,U8 | TLP292-4 | |
| U2 | AT24CS32-SSHM | I2C Serial EEPROM, 32Kb (4096x8) with Unique Serial Number, SO8 |
| U5 | LAN9252_PT | Ethernet Controller 10/100 Base-FX/T/TX PHY SPI Interface 64-TQFP-EP (10x10) |
| U6 | STM32F407VGT6 | STMicroelectronics Arm Cortex-M4 MCU, 1024KB flash, 192KB RAM, 168 MHz, 1.8-3.6V, 82 GPIO, LQFP100 |
| U7 | MAX3485CSA/ESA | True RS-485/RS-422, 10Mbps, Slew-Rate Limited, with low-power shutdown, with receiver/driver enable, 32 receiver drive capacitity, DIP-8 and SOIC-8 |
| U9 | AMS1117-3.3 |
| 1A Low Dropout regulator, positive, 3.3V fixed output, SOT-223 |
| B1-B7 | BLM18EG221S | Ferrite bead, small symbol |
|---|
| C1-C3,C6,C8,C10,C12,C14-C16,C18-C25,C28,C30,C32,CN3 | 0.1uF | 4 resistor network, parallel topology,Unpolarized capacitor |
|---|
| C4,C5 | 20pF | Unpolarized capacitor |
|---|
| C7 | 2uF | Unpolarized capacitor |
|---|
| C9 | 1uF | Unpolarized capacitor |
|---|
| C11 | 470pF | Unpolarized capacitor |
|---|
| C13,C17 | 2.2uF | Unpolarized capacitor |
|---|
| C26,C27 | 22pF | Unpolarized capacitor |
|---|
| C29,C31 | 10uF | Unpolarized capacitor |
|---|
| CN1,CN2 | 10pF | 4 resistor network, parallel topology |
|---|
| D1,D3,D5,D7,D9,D11,D13,D15,D17,D19,D21,D23 | Yellow led |
|---|
| D2,D4,D6,D8,D10,D12,D14,D16,D18,D20,D22,D24,D27 | Red led | Light emitting diode |
|---|
| D25 | Green led | Light emitting diode |
|---|
| D26 | Orange led | Light emitting diode |
|---|
| D28 | Blue led | Light emitting diode |
|---|
| D29-D31,D34 | White |
|---|
| D32,D33 | Blue | Light emitting diode |
|---|
| IN1,OUT1 | J0011D01BNL | LAN Transformer Jack, RJ45, 10/100 BaseT |
|---|
| J1 | In1-4 |
|---|
| J2 | In5-8 |
|---|
| J3 | In9-12 |
|---|
| J4 | 24V_Common |
|---|
| J5 | Serial usart1 | Generic connector, single row, 01x04, script generated |
|---|
| J6 | THCAD | Generic connector, single row, 01x04, script generated (kicad-library-utils/schlib/autogen/connector/) |
|---|
| J7 | STLINK | Generic connector, single row, 01x04, script generated |
|---|
| J8 | Output1-2 |
|---|
| J9 | 24V Field |
|---|
| J10 | Output3-4 |
|---|
| J11 | 5V input | Generic connector, single row, 01x02, script generated |
|---|
| R1-R3,R17,RN1,RN3,RN8,RN12 | 1k | 4 resistor network, parallel topology,Resistor |
|---|
| R4,R5,R19 | 2k | Resistor |
|---|
| R6 | 12.1k | Resistor |
|---|
| R7,R8 | 22 | Resistor |
|---|
| R9-R15 | 10k | Resistor |
|---|
| R16 | 120 | Resistor |
|---|
| R18,RN2,RN4,RN7,RN14 | 4k7 | 4 resistor network, parallel topology,Resistor |
|---|
| R100 | 100k |
|---|
| RN5,RN6 | 49.9 | 4 resistor network, parallel topology |
|---|
| RN9-RN11 | 39k | 4 resistor network, parallel topology |
|---|
| RN13 | 330 | 4 resistor network, parallel topology |
|---|
| SW1 | SW_Push | Push button switch, generic, two pins |
|---|
| Y1 | 25MHz | Two pin crystal |
|---|
| Y2 | 8 MHz | Two pin crystal |
|---|