Loading design…
DashiellRussell
| Reference | Value | Description |
|---|---|---|
| Q1 | DMG2301L | P-MOSFET transistor, gate/drain/source |
| Q2 | AO3401A | -4.0A Id, -30V Vds, P-Channel MOSFET, SOT-23 |
| Q3-Q5 | AO3400A | 30V Vds, 5.7A Id, N-Channel MOSFET, SOT-23 |
| U1 | STM32L452RETx | STMicroelectronics Arm Cortex-M4 MCU, 512KB flash, 160KB RAM, 80 MHz, 1.71-3.6V, 52 GPIO, LQFP64 |
| U2 | TPS63060 | Buck-Boost Converter, 2.5-12V Input Voltage, 2-A Switch Current, Adjustable 2.5-8V Output Voltage, S-PWSON-N10 |
| U3 | SPX3819M5-L-3-3 | 500mA Low drop-out regulator, Fixed Output 3.3V, SOT-23-5 |
| U4 | H3LIS331DL | 3-Axis Accelerometer, 2/4/8/16g range, I2C/SPI interface, LGA-16 |
|---|
| U5 | MS5611 #1 | Barometric pressure sensor, 10cm resolution, 10 to 1200 mbar, I2C and SPI interface up to 20MHz, LGA-8 |
|---|
| U6 | LIS3DH | 3-Axis Accelerometer, 2/4/8/16g range, I2C/SPI interface, LGA-16 |
|---|
| U7 | MS5611 #2 | Barometric pressure sensor, 10cm resolution, 10 to 1200 mbar, I2C and SPI interface up to 20MHz, LGA-8 |
|---|
| U8 | USBLC6-2SC6 | Very low capacitance ESD protection diode, 2 data-line, SOT-23-6 |
|---|
| U9-U11 | PC817 | DC Optocoupler, Vce 35V, CTR 50-300%, DIP-4 |
|---|
| BZ1 | Buzzer | Buzzer, polarized |
|---|
| C1,C2 | 27pF | Unpolarized capacitor |
|---|
| C3,C5,C6,C8,C10,C11,C13,C17,C24-C28,C30 | 0.1uF | Unpolarized capacitor |
|---|
| C4,C9,C21,C22,C29 | 1.0uF | Unpolarized capacitor |
|---|
| C7,C23 | 10nF | Unpolarized capacitor |
|---|
| C12 | 4.7uF | Unpolarized capacitor |
|---|
| C14,C15 | 10uF | Unpolarized capacitor |
|---|
| C16,C18,C20 | 22uF | Unpolarized capacitor |
|---|
| C19 | 10pF | Unpolarized capacitor |
|---|
| D1 | 5.1V | Zener diode |
|---|
| D2,D8 | B5819W | Schottky diode, small symbol |
|---|
| D3-D7 | Green | Light emitting diode |
|---|
| D9,D15 | LED_RED | Light emitting diode |
|---|
| D10,D12 | LED_YELLOW | Light emitting diode |
|---|
| D11,D13 | SMAJ15A | 400W unidirectional Transient Voltage Suppressor, 15.0Vr, SMA(DO-214AC) |
|---|
| D14 | LED_RGB | RGB LED, 6 pin package |
|---|
| D16 | LED_GREEN | Light emitting diode |
|---|
| F1 | 1A | Resettable fuse, polymeric positive temperature coefficient |
|---|
| J1 | SWD |
|---|
| J2 | Micro_SD_Card_Det1 | Micro SD Card Socket with one card detection pin |
|---|
| J3 | USB_C_Receptacle_USB2.0_16P | USB 2.0-only 16P Type-C Receptacle connector |
|---|
| J5 | Conn_01x04 | Generic connector, single row, 01x04, script generated (kicad-library-utils/schlib/autogen/connector/) |
|---|
| J7 | J_PYRO1 | Generic screw terminal, single row, 01x02, script generated (kicad-library-utils/schlib/autogen/connector/) |
|---|
| J8 | J_PYRO2 | Generic screw terminal, single row, 01x02, script generated (kicad-library-utils/schlib/autogen/connector/) |
|---|
| J9 | J_PYRO_BAT | Generic screw terminal, single row, 01x02, script generated (kicad-library-utils/schlib/autogen/connector/) |
|---|
| J10 | J_BATT | Generic screw terminal, single row, 01x02, script generated (kicad-library-utils/schlib/autogen/connector/) |
|---|
| JP1 | RESET_JMP | Jumper, 2-pole, open |
|---|
| L1 | 1µH | Inductor |
|---|
| R1,R6,R15,R22,R23,R25,R28,R29,R31,R37 | 10k | Resistor |
|---|
| R2 | 620k | Resistor |
|---|
| R3-R5,R21 | 100k | Resistor |
|---|
| R7 | 33k | Resistor |
|---|
| R8-R10 | 4.7k | Resistor |
|---|
| R11,R12,R19,R24,R30,R38,R39 | 1k | Resistor |
|---|
| R13,R14 | 5.1k | Resistor |
|---|
| R16,R26,R32 | 3.3k | Resistor |
|---|
| R17 | 0 | Resistor |
|---|
| R18,R20,R27 | 330 | Resistor |
|---|
| R33-R35 | 100 | Resistor |
|---|
| R36 | 150 | Resistor |
|---|
| TP1-TP10,TP12 | 1.0mm | Test Point |
|---|
| Y1 | 8MHz | Four pin crystal, GND on pins 2 and 4 |
|---|